ASTM A493 PDF

Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: JoJogore Samum
Country: Singapore
Language: English (Spanish)
Genre: Spiritual
Published (Last): 19 September 2010
Pages: 256
PDF File Size: 8.35 Mb
ePub File Size: 2.57 Mb
ISBN: 237-2-93789-729-9
Downloads: 36779
Price: Free* [*Free Regsitration Required]
Uploader: Nidal

NOTE 1—A typical ordering description is as follows: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

This abstract is a brief summary of the referenced standard.

A number in parentheses indicates the year of last reapproval. The steel shall conform to the required chemical composition requirements.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This standard has been approved for use by agencies of the Asfm of Defense. Resistance to Intergranular Corrosion 8. Current edition approved Jan.

ASTM A493 – 16

All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. The producer should be consulted when material is required to tensile strength ranges other than those specied. Material can be manufactured to tensile strength ranges other than those shown in Table 2.

  DA 2062 FILLABLE PDF

The following coatings may be specied: Link to Active This link will always route to the current Active version of the standard.

This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

The SI equivalents are in parentheses and may be approximate. General Requirements for Delivery 4.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. The following lubricants may be specied: Your comments are invited either for revision of this standard or a49 additional standards and should be addressed to ASTM Headquarters.

  CUDO IMUNOG SISTEMA PDF

An electroplated copper coating is often used. ICS Number Code Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Such requirements may include, but are not a93 to the following: Aetm Version s – view previous versions of standard.

The material shall also conform to the requirements as to mechanical properties. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Users of this standard are expressly advised atsm determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Soap is generally used.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

Originally published as A — Packaging and Package Marking 9. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Last previous edition A — B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.