1 fan ( mm). Connectors be quiet! Straight Power BQT EW. Type of connector for the motherboard: 20+4 pin. Number of connectors 4-pin CPU: 2. The be quiet! Straight Power BQT E The be quiet! BQ T E W. W. 6W. 12,5 W. 30A. 30A. 0,5A. W. – Va c. 50 – 60Hz. 10 – 5A. W. Be quiet! no unknown quantity is surely manufacturer, if it concerns power packs. In Silencerkreisen by the earlier P5 and P6 and the.

Author: Faugore Kalrajas
Country: Barbados
Language: English (Spanish)
Genre: Spiritual
Published (Last): 17 April 2006
Pages: 405
PDF File Size: 5.94 Mb
ePub File Size: 20.54 Mb
ISBN: 552-1-25751-652-1
Downloads: 96431
Price: Free* [*Free Regsitration Required]
Uploader: Faejora

So then I was wondering if this uF cap could be replaced with a uF one? The time now is Information about filters The filter functions help you to find the best products. I can’t see an issue with using ultra low ESR caps on a standby output. FWIW, It’s about 2. Thessaloniki, Greece My Country: Eigentlich niemand — aber es is I’d suggest replacing the fan while you’re at it. Dark Power PRO These would be much easier to get.

Number of reviews Excludes all products with a lower number of reviews that your choice. Core i7 K 3.

Be quiet! Straight Power E5 500W

Straight Power E7 W. No wonder it doesn’t work! I’d say just try it with the HM and see if it works, since they are the only reliable 8mm uF 6. Reviews page 1 of 1. Their plight, in fact is even worse, they don’t realize that they’re cantonists, they think they’re free men. Be Quiet Dark Power W.


Pure Power 11 W NikkTech. Be Quiet Dark Power Pro w.

be quiet! Straight Power BQT EW Power Supplies specifications

What’s also interesting in the second cap is, that it was covered with a rubber “sock”, best seen in the last picture. Straight Power 10 W.

Pure Power 10 CM. Be Quiet System Power 9 W.

Dark Power Watt. Ebay sure can find fake bqf from china with appropriate size, but that’s another thing. Tweak it until you find a good idle speed, and once you’re happy with it, remove it and measure the resistance, and find a resistor which is approximately what you had the pot set to, although be careful r5-500w to move the knob when you’re removing the pot. Dark Pwer Pro 11 W. Dark Power Pro P8 W.

System Power S8 W.

e5-00w Or they could be for the standby, but causing problems when the computer tries to start – as it will draw a bit more from standby on start up. Find More Posts by Scenic. System Power 8 W.

Be Quiet BQT EW recap, odd sized CapXon The only way to add a resistor or a pot temporarily to the thermistor is by soldering it in on the bottom of the PCB, as the thermistor is underneath the secondary side heatsink and some E5’s have so much e5-500e gunk in that area that you can’t even see the little TO92 transistor right next to it let alone see the thermistor pins because it’s covered in that stuff.


I’ll post some updates when I’ve done the recapping and the possible fan replacement, or if I run into any additional problems. Dark Power Pro P11 W. Be Quiet Straight Power 10 W. Ah, the plague of CapXons continues. This is my first time posting though, as I’ve run into a problem. Power Zone W.

BeQuiet Straight Power System Power 7 W. The only way to add a resistor or a pot temporarily to the thermistor is by soldering it in on the bottom of the PCB The attached photos are from a E parts unit. Remember, both fans on the SP-xxx are controlled by the same thermistor. Pure Power 9 W.