SINAMICS S Equipment Manual for Booksize Power. Units. • SINAMICS S Equipment Manual for Description of the LED states of a CU SINAMICS S Equipment Manual for Booksize Power Units .. CU DP from firmware version with integrated Ethernet interface. ○ Smart Line. Siemens SINAMICS S Manual Online: Control Unit (cu), Description, Safety Information. Control Unit (CU) Description The CU

Author: Yozshukasa Sakus
Country: Azerbaijan
Language: English (Spanish)
Genre: Health and Food
Published (Last): 24 November 2005
Pages: 341
PDF File Size: 18.38 Mb
ePub File Size: 3.45 Mb
ISBN: 642-5-20618-191-3
Downloads: 28353
Price: Free* [*Free Regsitration Required]
Uploader: Kazigar

Electronically coordinated single drives work together to perform the drive tasks. Ring Alert Type To secure the cable in accordance with EMC requirements, snap the clip onto the shield plate. Hazardous shock voltages caused by, for example: It is essential that the Active Interface Manuaal matched to the output type is used block diagram, see Active Line Modules in chassis format. IP21 degree of protection with canopy option M21?

Prices Where to Buy. Function test with no motor connected Unit acceptance in presence of customer: For this purpose, you are advised to wear a grounded ESD wristband. This option is recommended in particular for Line Modules together with Line Connection Modules since, in this case, the Line Connection Module must be equipped with a pre-charging DC link or line reactors depending on the type of Line Modulein addition to the electrical interface mounted on a mnaual.

LG CU320 Manuals

Feed the cable for the CU Control Unit into the cabinet from the bottom left. Trademarks All names identified by?

Inicio De Media Net Specific Absorption Rate DRIVE-CLiQ is an internal serial interface of the drive that enables fast and easy configuration of the complete drive line-up with prefabricated cables in varying lengths.


This requires cyclic data exchange between the CNC and all the drives.

Orange Steady light — Off Notice You must ensure that the connected encoder can be operated with a 24 V supply. For this reason, the unit should not be opened until a reasonable period of time has elapsed.

Caution The cooling clearances of du320 mm above and below the components must be observed. Checklist Table 4- 1 Item 1 2 Electrical installation: If necessary, reattach the protective covers and doors. Coordinated drives that carry out a drive and motion task together are used in many mechanical and plant engineering applications. The CU DP has the following interfaces ports: S Vu320 bright if at least one parameter was changed and the value was not transferred into the nonvolatile memory.

This can be achieved using EMC screwed glands on the motor end and EMC shield clips on the converter end, for example. Active Line Modules draw a virtually sinusoidal current from the supply system and cause virtually no line harmonic distortions.

SINAMICS S120 drive system

Smart Line Modules can feed energy to the DC link of a drive group through a non-stabilized converter and also feed back the generated excess energy into the power supply system. For more information about the interfaces of available options, refer to the relevant sections in this manual. Connect the signal cables to the terminal blocks. Ensure that the ground at the installation location is strong enough to bear the weight of the cabinet units.

Are all of the prerequisites for commissioning checked and were the points in the manusl for commissioning checked refer to Chapter 2?

Download Free MT Manual & Driver | Million Tech

For motors, for example, these data include the parameters of the electric equivalent circuit diagram and characteristic values for mannual built-in motor encoder. Particularly suitable for multi-axis applications Coordinated drives that carry out a drive and motion task together are used in many mechanical and plant engineering applications. Suitable hoisting gear operated by trained personnel is also required due to the weight of the cabinet units.


Preparatory steps Before starting any cabling or connection work in the Cabinet Modules, ensure that the following measures are performed: Exceptional temperatures as well as emissions of ch320, noise, particles, or gas caused by, for example: Message Alert Tones cu3320 If a brake is being used, is it correctly controlled see Function Manual?

This can be done as follows: The clearance around an open door escape route specified in the applicable accident prevention guidelines must be observed. These require drives with a connected DC link, which allows mankal energy balancing between braking and driving axes.

The cabinet units must not be tipped and transported in a horizontal position. Setting Up A Conference Call The neutral conductor is left on terminal “0” and the phase is clamped to the existing line voltage.

Cingular mall, Shop tones, Shop games | LG CU User Manual | Page 57 / 99

When a Smart Line Module is used as the infeed, the matching line reactor must be installed. Green Red Flashing light 0. The commissioning requirements have been met. Guide the cable up and, when it reaches the level of the line connection, guide it to the left.