SINAMICS S Equipment Manual for Booksize Power. Units. • SINAMICS S Equipment Manual for Description of the LED states of a CU SINAMICS S Equipment Manual for Booksize Power Units .. CU DP from firmware version with integrated Ethernet interface. ○ Smart Line. Siemens SINAMICS S Manual Online: Control Unit (cu), Description, Safety Information. Control Unit (CU) Description The CU
|Genre:||Health and Food|
|Published (Last):||20 October 2010|
|PDF File Size:||20.43 Mb|
|ePub File Size:||1.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Such personnel must be thoroughly familiar with all the warnings and maintenance procedures for the cabinet described in the documentation provided.
Siemens SINAMICS S120 Manual: Control Unit 320 (cu320); Description; Safety Information
Joint hardware and software components, as well as standardized tools for design, configuration, and commissioning tasks ensure high-level integration across all components. The plant operator is responsible for taking appropriate measures labels and hazard warnings to adequately protect operating personnel and others against any possible risk.
During A Call Quick view Screen Size. To protect the machines and personnel, the relevant safety regulations must be carefully observed. Gently press the jumper against the auxiliary voltage busbars to be connected on the left and right until the jumper engages.
Download Free MT Manual & Driver | Million Tech
These differences are intentional and exist for “EMC optimization” reasons. The clearance between the top of the cabinet and the ceiling is shown in the diagram below. mamual
Shutdown path p Control unit CU X Table of contents Table Of Contents The main differences are: An external, MicroSD expansion slot is available for increased storage capacity. In particular, the general and national installation and safety guidelines for high-voltage installations e.
Are the mechanical end stops available and tightly bolted to both ends of the traversing path? Figure Setting terminals for the fan transformers to V 2 AC Figure Setting terminals for the fan transformers to Cu3200 2 AC The line-voltage assignments for making the appropriate setting on the fan transformer are indicated in the following table.
The related very steep switching edges of the converter output voltage and also, therefore, of the common-mode voltage cause correspondingly high capacitive currents and voltages on the machine’s internal capacitances. The main components of the system are as follows: The storage period should not exceed two years. Data set 0 is preset. Kanual heat sink, with its cooling fins and the fan module cu302 of the scope of supplyprotrudes through the back into a separate ventilation duct, which can also be open to the outside.
Remove the cover 4.
Preguntas Y Respuestas The following versions are available: Modules must not come fu320 contact with highly insulating materials such as plastic parts, insulated desktops, articles of clothing manufactured from man-made fibers. DRIVE-CLiQ is an internal serial interface of the drive that enables fast and easy configuration of the complete ,anual line-up with prefabricated cables in varying lengths. The tripping current on the line-side must be set according to the conditions of the system.
Connect the cable to the terminals.
Feed the cable for the CU Control Unit into the cabinet from the bottom left. Tighten the nuts tightening torque: Ensure that the ground at the installation location is strong enough to bear the weight of the cabinet units.
Even at full infeed capacity, no unnecessary heat is generated in the control cabinet. The selected project is displayed at the top left. Before mounting the side panels on an installed cabinet row, you must remove any jumpers present in the DC busbars of the cabinet on the right.
Cable routing Cable for supply infeed Signal cables Notice: The cooling air supply and exhaust must not be obstructed and must be available in sufficient quantity. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. Checklist Use the checklist below to guide you through the electrical installation procedure for the cabinet.
Table of contents User Guide The power-on disable function prevents the drive unit from being restarted.
SINAMICS S Equipment Manual Cabinet Modules_图文_百度文库
In addition to the danger and warning information provided in the technical customer documentation, the applicable national, local, and plant-specific regulations and requirements must be taken into account. Prior to performing the voltage test for electrical equipment of industrial machines in accordance with ENSection Hora De Datos Death, serious injury, or substantial material damage can result if these factors are not taken into account.
The maximum movement can be: An auxiliary voltage busbar system spanning the individual Cabinet Modules supplies the required auxiliary voltages for the equipment fans and the 24 V DC loads. LG released the CU on March 23, These are shown in the following table.
These require drives with a connected DC link, which allows cost-saving energy balancing between braking and driving axes.
Place barriers around hazardous areas. Making A Second Call Note In the case of transport units with standard integrated DC busbars within the cabinet group, you only need to connect the ends of the busbars of the transport units.