JBL H (8Ohm). Unavailable. Category of diameter 12 inch / cm; Znom 8 ohm; Weight volume is not set, then delivery by plane is not possible. Brand New JBL H 12″ Aftermarket Recone Kit, 8 ohm. Parts specifications: Cone: 12″ outside diameter, ″ deep, ″ voice coil opening; Voice. Subwoofer JBL H. General specifications: diameter 12 inches, maximum power W. Thiele-Small parameters: frequency of self resonance Fs=75 Hz, .

Author: Mauk Meztigami
Country: New Zealand
Language: English (Spanish)
Genre: Relationship
Published (Last): 28 August 2006
Pages: 124
PDF File Size: 2.1 Mb
ePub File Size: 3.10 Mb
ISBN: 300-6-63026-202-9
Downloads: 48209
Price: Free* [*Free Regsitration Required]
Uploader: Kazira

jbk Basically the K, K, and shared the same magnet structure, including the top plate. February 24, That is a factor determined by the enclosure and crossover. Read times Brian Elstro Jr. You will have created something.

Extra Tabs by vBulletin Hispano. From what I’ve been able to understand, is that the is JBL’s new king of midrange Logged “can you make them sing better? With proper processing do you think that it would be a good idea to just stick the in and work it out, while re-coning the JBL, The is all its own and is even less a woofer, it’s dynamite about Hz nbl above.

Blew a in the monitor older mr series due to a broken handle overexcursion Ivan Beaver on February 19, All that being said, my original post was pre-emptive of checking the VC, which didnt seem to be effected at all. You will get an enormous reward. The letter following the is used to designate the impedence. February 21, Another question, can the be reconed to the specs better LF handling?


It’s really a mid-range, a mid-bass at best.

JBL 2022H 12-inch speaker unit

I’ve been thinking of replacing my ‘s with ‘s down the road a bit and if ‘s can be reconed as ‘s then that could be an option I used to do that all the time-and the speakers were very “workable”. Generally it will be more like the kit you put in it than the original-but will not have the exact same performance. Ditto E, E, and Last edited by maxwedge; at There was a ridge left behind from the old dustcap glue so I had to score the new cone near the former to get it to lay down flat, but once all the pre-fit was done, glue-ing it in wasnt too big of an issue rubber cement I’m not aware of it ever being used in a 3-way app as a mid driver.

I have compared these side by side and could not find any difference in 2202h basket. Results 1 to 5 of 5. February 19, One starting point in my confusion I read that someone re-coned a to aincreasing x-maxx how Thanks to everyone, good info all around.

Since the taper of the drivers was different I had to cut 202h2 new cone at an angle and push it to fit the taper. I do have a set of ‘s sitting around but they are the midrange version. I thought the magnet slab was thicker. I guess you would call it JBL’s “midline” series driver.


Brian Elstro on February 18, The letter suffix represents the impedance, not frequency range of the speaker. Logged Brian Elstro Jr. Differences were achieved in cone composition, coil windings, and VC former material. This message comes from JBL Dog. I think they both fall inbetween the “producer” and “reproducer” sound Dance to the radio. Please login or register. Like every job, it had it’s ups and downs.

JBL H 12″ Woofer Speaker Driver 8 Ohm | eBay

All times are GMT However the magnet structures and magnetic energy focusing are different-so you will end up some sort of “half breed”. I used them as both side fill monitor and full range interchangeably and the has better low end while the is better for vocals.

I was under the thought that the suffix was also something that showed intent or 22022h of the driver eg- a single driver with a 16ohm impedance 2022g be used for a total 3 or 4 way system impedance of 8 ohms, but a single 4 ohm driver would be used for a 2 way system impedance of 8 ohms By that I mean the kits will interchange physically.

Ie putting a kit in an E and so forth.